ANSI Cut Levels A1–A9 by Industry: Which Gloves Fit Which Jobs?
One worker is checking small parts in a warehouse. Another is fitting a sharp-edged HVAC duct. Across the factory, a press operator's team is moving freshly stamped steel parts. All three jobs involve handling materials, but the cut hazards are very different.
That's why asking “What ANSI cut level does my industry need?” is only the starting point. The better question is: What could cut a worker's hand during this particular task? ANSI/ISEA 105-2024 is a voluntary classification standard; OSHA does not prescribe one A-level for every job in a named industry.
This guide matches ANSI/ISEA cut levels A1 through A9 with common jobs in warehousing, assembly, construction, HVAC, automotive production, glass handling, metal stamping, and recycling—while explaining when a higher rating may be necessary.
Cut Levels by Job: The Quick Answer
| Example levels to investigate* | Common tasks to evaluate | Typical setting |
|---|---|---|
| A1–A2 | Inspection, packing and light handling with minor incidental cut exposure | Warehouse, distribution, light assembly |
| A3–A4 | Assembly with occasional sharp edges; some light metal tasks may lead an assessor to consider A4 | Automotive suppliers, general manufacturing, construction |
| A5–A6 | More demanding sheet-metal, glass or fabricated-part handling when assessment supports A5–A6 | HVAC, metal fabrication, automotive, glass operations |
| A7–A9 | Severe cut exposure from sharp irregular metal, scrap or blades during isolated maintenance | Metal stamping, recycling, heavy fabrication, certain blade-maintenance tasks |
*These are editorial groupings to explain possible job exposures, not official ANSI/ISEA or OSHA industry-to-rating assignments. The final selection requires a workplace hazard assessment and documented glove performance.
What the published task guide actually says: The U.S. Army Corps of Engineers' 2024 EM 385-1-1, Table 5-6 uses A1 for very light cut hazards, A2–A3 for light/medium, A4–A6 for medium/high hazards including sheet-metal handling and HVAC work, and A7–A9 for high/extreme hazards. The table gives typical tasks, not a rating automatically required for everyone in those industries. This USACE manual has a defined scope covering USACE activities and applicable contracts; it is not a general OSHA mandate for every U.S. employer.
First, What Does A1–A9 Actually Measure?
The ANSI/ISEA 105-2024 classification uses nine cut-resistance levels. The higher the number, the greater the blade-cut force required in the specified laboratory test. The cut rating describes tested resistance to a specified smooth-blade action; by itself, it establishes neither puncture, heat, chemical, electrical nor impact protection. Performance may also differ across glove materials or areas, so verify what was tested.
What changed in the 2024 standard?
ANSI/ISEA 105-2024 retained the nine cut levels while introducing a standardized pentagon marking that shows cut, abrasion and puncture classifications separately. A cut rating cannot stand in for an abrasion or puncture test; an “X” means a particular property is not tested or not applicable. See the ISEA 2024 marking guidance and PIP's illustrated standard update.
A critical limitation: ASTM F2992-23 measures resistance to a controlled smooth-blade cutting action. It does not replicate serrated blades, powered cutters, puncture or every workplace cutting hazard. Assess those risks separately.
Think of the numbers as a way to compare laboratory cut performance, not a promise that a glove will stop a knife, spinning blade, needle or every sharp edge on the job. Read the manufacturer's test documentation for the complete glove and its intended protection area.
A1–A2: Light Handling, Warehousing and Packaging
A1–A2 may be worth investigating only when a task involves minor incidental cutting exposure and dexterity matters. Examples include some inspection, sorting, small-parts handling, packing and receiving operations. A task with no relevant cut hazard may not call for a cut-rated glove; a warehouse task involving blades, metal strapping or sharp components may need considerably more protection. USACE's published task grouping places A1 by itself and A2 together with A3.
- A1: A possible starting point for light inspection, packing and handling clean, non-sharp components where only incidental minor cut hazards exist.
- A2: Worth comparing when light assembly or warehouse work introduces slightly more contact with edges, such as metal fasteners, wire components or moderately rough parts.
Where the range can fall short: Don't assume every warehouse role belongs in A1–A2. Employees using exposed utility blades, handling steel strapping, broken glass or unprotected sharp metal may face very different hazards—even in the same building.
A3–A4: Assembly Work, With Different Requirements for Sharp Edges
As workers encounter more exposed edges, intermediate cut ratings may be assessed for automotive and appliance assembly, repairs, construction material handling and some metal-component tasks. However, A3 and A4 fall into different USACE example bands; don't treat them as a standard paired requirement.
- A3: A possible option for repetitive handling of small components with occasional rough or moderately sharp edges.
- A4: A common starting comparison for some sheet-metal and metal-assembly tasks. USACE places sheet-metal handling and HVAC examples within the broader A4–A6 band, depending on task conditions.
For example, a technician connecting prefinished ductwork may face a different cut hazard from a worker sorting freshly cut duct sections with unfinished edges. The work description sounds similar; the exposure is not.
A5–A6: More Demanding Sharp-Edge Work in Metal, HVAC and Glass
For tasks involving frequent contact with sharper, unfinished or burred edges, A5–A6 can be a useful range to evaluate. Examples may include particular sheet-metal fabrication operations, stamped automotive components, unfinished HVAC ductwork and certain glass-handling tasks. But A5–A6 is not the minimum requirement for the sheet-metal industry: USACE's typical-task table covers sheet-metal handling, HVAC and glass handling under the broader A4–A6 band. Evaluate the specific edge condition, handling method and other hazards first.
- A5: One level to assess for exposed or burred sheet-metal edges and other fabricated-part handling, when an A4 glove does not provide the required risk reduction.
- A6: Worth comparing when the hazard assessment calls for more laboratory cut resistance than an A5 glove provides; evaluate actual edge exposure, grip and the glove's full tested performance.
What else matters? Steel may be oily, glass may be slippery and heavy panels may be harder to control. These factors affect handling risk but do not convert directly into a mandatory A-level. Check coating, wet/oily grip, fit, dexterity and abrasion performance. For glass, assess edge exposure, breakage and separate puncture or impact hazards; use engineered handling controls where appropriate.
A7–A9: Metal Stamping, Recycling and Extreme Sharp-Edge Hazards
At the upper end of the scale, workers may encounter large stamped parts, jagged scrap, heavy metal blanks, sharp manufacturing offcuts, or industrial blades during properly isolated maintenance. A7–A9 is the range to investigate for the most serious cut exposures—not a universal requirement for everyone employed in these industries.
- A7: One option to assess for severe manual sharp-edge exposure in metal fabrication, stamping and some recycling operations, with site controls and safe handling procedures.
- A8: Consider when the risk assessment indicates the need for a higher tested cut classification, for example certain particularly demanding sharp-metal or glass-handling tasks.
- A9: Evaluate only where an extreme cut exposure justifies the highest laboratory cut classification. A9 is not cut-proof and does not make contact with powered blades, sharp points or machinery safe.
Consider a metal-stamping facility: an operator may inspect clean, deburred parts at one station and a second worker may handle unfinished stamped blanks at another. The first worker does not automatically need the same glove as the second. Likewise, a recycling worker sorting intact cardboard is not exposed to the same hazards as someone handling sharp scrap metal.
Important: High-cut gloves do not make it safe to contact moving blades or unguarded equipment. Blade changes and machine maintenance require appropriate isolation/lockout procedures, safeguards and task-specific PPE. Gloves themselves can also create entanglement hazards around certain rotating machinery.
Machine-guarding note: OSHA's machine-guarding guidance addresses rotating parts and other moving-machine hazards. Never rely on a high cut rating to justify wearing gloves near equipment where gloves could snag or become entangled; follow machine-specific safe work practices and required isolation procedures.
One Industry, Several Cut Levels: Why the Task Wins
The most useful question for a safety manager is not simply “Automotive, HVAC or recycling?” It is “What does this worker touch, how sharp is it, and how often can the hand make contact?”
Within one automotive plant, packing finished plastic components may be a low-cut task, subassembly with burrs may call for an intermediate rating, and handling freshly stamped metal can justify a high-cut evaluation. Job title and industry sector cannot substitute for examining the actual edge exposure.
The U.S. Army Corps of Engineers EM 385-1-1 (2024), Table 5-6 provides practical examples across cut levels. Those examples are useful for orientation; they are not a universal rating mandate for every worksite.
Job-Specific Comparison: The Same Industry Can Need Different Gloves
Use this as an assessment prompt, not a mandatory PPE allocation chart. The example ranges synthesize the USACE EM 385-1-1 work-task examples, Ansell's ANSI/ISEA 105-2024 application guide and the OSHA task-based selection rule.
| Industry | Example lower-exposure task | Example higher-exposure task | What to check |
|---|---|---|---|
| Warehouse / logistics | Boxed-goods packing or inspection: consider A1–A2 if cut hazards are minor | Handling sharp metal strapping or exposed components: evaluate higher ratings | Strapping, blades, damaged packages and grip |
| Automotive | Inspecting finished, deburred components: lower or moderate range may suffice | Handling unfinished stamped metal: use task assessment; A4–A6 or A7–A9 may be indicated by severity | Burr severity, oil, part weight and handling frequency |
| HVAC / construction | Handling finished/deburred duct parts: assess edge exposure; USACE lists HVAC within A4–A6 | Handling freshly sheared or burred metal: assess A4–A6 or higher if justified | Fresh cuts, folds, fasteners and required dexterity |
| Glass operations | Protected or finished panels: select by assessed contact with edges | Unprotected glass edges or breakage cleanup: evaluate higher cut and other protections | Breakage, puncture and handling system |
| Recycling / sorting | Separated cardboard or clean materials: assess lower-cut needs | Irregular sharp scrap and broken materials: evaluate A5–A9 and puncture risk | Unknown edges, contaminants, needles and sharp protrusions |
Reading this table: “Consider” and “evaluate” are deliberate. No row establishes an OSHA-required cut level. A formal hazard assessment, product test reports and site-specific procedures determine the actual selection.
Standards also differ across markets. The SATRA EN 388 technical explanation describes separate abrasion, cut, tear, puncture and optional impact tests; its EN ISO 13997 cut scale uses A–F, not the U.S. ANSI A1–A9 numbering. Do not treat an EN 388 “F” as the same label as ANSI “A9.”
For comfort and control, evaluate glove gauge and palm coating alongside the cut level. Superior Glove's technical overview explains how engineered yarn, glove construction and grip design affect use; a higher cut score does not replace on-the-job fit and dexterity checks.
A Five-Question Checklist Before Selecting Cut Gloves
- What creates the cut? Cardboard edges, burrs, sheet metal, glass, scrap or blades?
- How severe and frequent is contact? An occasional brush against a smooth edge is different from repeated handling of jagged metal.
- What other hazards exist? Puncture, impact, heat, chemicals, electricity, slippery surfaces or machinery entanglement?
- Can workers actually do the job in the glove? Check fit, grip, dexterity, usable sizing and wear life.
- What does the product testing show? Confirm the exact glove's ANSI/ISEA 105 cut rating, relevant protection area and any separate performance requirements.
As OSHA explains in 29 CFR 1910.138, appropriate hand protection must be selected from its performance characteristics relative to the identified hazards, task, work conditions and duration of use. OSHA does not assign a fixed ANSI A-level to all workers in a particular industry.
Quick FAQs
Is A9 always better than A4 or A6?
A9 offers a higher tested cut-resistance classification. But it is not automatically the best glove for a particular job: grip, flexibility, fit, comfort and other protection requirements still matter. The right glove is the one that addresses the assessed hazards without interfering with safe work.
Can A1–A2 gloves be used in construction or automotive work?
Yes, potentially, for specific lower-exposure tasks. Other jobs at the same site—especially handling freshly cut metal, sharp offcuts or exposed blades—may require much higher protection. Assess the specific work activity.
Does an A7 or A9 rating protect against needle punctures or chemical exposure?
No. Cut ratings do not establish needle-puncture or chemical protection. Those properties require separate evaluations and test data. The ISEA hand-protection guidance distinguishes these hazards.
Do I need the same cut rating for every worker on the line?
Not necessarily. It can be more effective to assess stations separately and choose gloves according to the material, task and risks present, while following site rules and ensuring compatible protective equipment.
The Bottom Line
A1–A2 may be evaluated for low-cut-exposure packing and handling tasks, while A3–A4 can enter the selection process for assembly and progressively sharper edges. For sheet-metal, HVAC and glass handling, USACE's published typical-task range is A4–A6; A5–A6 may be appropriate for certain more demanding tasks within that range. A7–A9 belongs in the assessment of particularly severe cut exposures such as sharp metal stamping, heavy fabrication and scrap handling.
But none of these is an industry-wide guarantee. Start with the real task, verify the glove's tested performance, and consider grip, fit and all other hazards before choosing.
For more detail on rating interpretation, read our guide to choosing cut-resistant gloves. If grip and coatings are part of the decision, see our coated work glove comparison.
References & Further Reading
Technical sources checked November 2026. These 12 references include regulatory texts, standards bodies, a test-method listing, a testing organization, a USACE safety manual and manufacturer guidance. Industry applications are examples rather than official ANSI-to-job assignments. The USACE manual applies within its specified USACE and contract scope; OSHA's regulations require assessment-based selection rather than a universal A-level.
- ANSI — ANSI/ISEA 105-2024: Cut Levels Explained (2025; updated 2026)
- ISEA — Hand Protection and the ANSI/ISEA 105-2024 Standard
- ISEA — ANSI/ISEA 105-2024 Labeling Usage Guidelines (2024, PDF)
- OSHA — 29 CFR 1910.138: Hand Protection
- OSHA — 29 CFR 1910.132: PPE Hazard Assessment and Selection
- U.S. Army Corps of Engineers — EM 385-1-1, Table 5-6: Cut Resistance Levels and Typical Tasks (2024, PDF)
- ASTM International — ASTM F2992-23: Cut Resistance Test Method
- Ansell — Guide to Understanding Cut Resistance Under ANSI/ISEA 105-2024 (PDF)
- PIP — ANSI/ISEA 105-2024 Cut, Abrasion and Puncture Classification Guide (PDF)
- Superior Glove — Everything You Need to Know About Cut-Resistant Gloves
- SATRA — EN 388:2016+A1:2018 and EN ISO 13997 Test Methods
- OSHA — Machine Guarding: General Requirements