How to Choose Cut-Resistant Gloves That Fit the Job

A cardboard edge, a piece of sheet metal, and a kitchen knife can all cut a hand. But they don't create the same risk. So why do some gloves say ANSI A2 while others say A5 or A9? And does a higher number always mean a better glove? Here is how to read cut ratings—and choose hand protection for the work actually being done.

Cut Resistance in 30 Seconds

Cut-resistant does not mean cut-proof. It means the glove material has been tested for its ability to resist a cutting blade under specific laboratory conditions. The higher the ANSI cut level, the greater the cutting load the material resisted in that test.

The catch? A glove can perform well in a cut test and still be wrong for a job if it offers poor grip, does not fit correctly, or does not protect against the task's other hazards.

What Does ANSI A1–A9 Actually Tell You?

Think of the nine ANSI levels as a measurement scale, not nine job titles. Under ANSI/ISEA 105-2024, A1 through A9 describe progressively higher tested cut resistance. The number comes from a standardized blade test—not from someone trying the glove against every sharp object on a factory floor.

Understanding ANSI Cut Levels
ANSI/ISEA 105-2024 • Laboratory cut test classifications
A1–A3Lower cut resistance
A4–A6Moderate to high
A7–A9Higher cut resistance
A1
200–499 g
A2
500–999 g
A3
1,000–1,499 g
A4
1,500–2,199 g
A5
2,200–2,999 g
A6
3,000–3,999 g
A7
4,000–4,999 g
A8
5,000–5,999 g
A9
6,000+ g

Grams refer to the standardized laboratory cut-test load, not the weight of an object that a glove can safely handle. Higher levels indicate higher tested cut resistance—not cut-proof protection.

Three useful ways to read the scale: A1–A3 indicate comparatively lower test resistance; A4–A6 indicate higher resistance; A7–A9 indicate some of the highest classifications. That is a way to understand the chart, not a prescription for a particular workplace. OSHA requires glove selection to reflect the actual task, conditions, and hazards.

Three Jobs. Three Different Questions.

1. Picking cartons in a warehouse. Are the edges merely rough, or do workers also use exposed blades to open packages? How much finger movement and grip do they need? A bulky glove that makes box handling awkward can introduce problems of its own.

2. Handling unfinished sheet metal. Are there burrs or razor-sharp edges? How heavy are the parts? Workers may need greater cut resistance, but also abrasion resistance and secure grip. The edge and handling motion matter just as much as the label.

3. Working with knives in food preparation. Where might the blade contact the hand? Is food-contact suitability necessary? A cut rating is only one part of the assessment, alongside fit, hygiene, the work method, and any specific requirements for knife tasks.

The lesson: Start with the hazard, then choose a suitable glove. Never start with “What's the highest number we can buy?”

Why Two Gloves With the Same Cut Rating Can Feel Different

Not all cut resistance comes from thick, stiff fabric. Manufacturers may combine HPPE/UHMWPE, aramid fibers, glass fibers, steel reinforcement, or other engineered yarns. The yarn blend, knitting, coating, fit, and thickness can produce very different experiences even when two gloves share the same cut level.

How the Materials Differ

HPPE / UHMWPELightweight engineered yarns
AramidStrength and some heat tolerance
Composite BlendsMay combine glass or steel with fibers

Simplified fiber illustrations, not microscopic photos. Actual protection depends on the finished glove's tested construction.

For a worker sorting small components all day, dexterity and comfort matter. For someone moving rough metal parts, secure grip and abrasion durability may be equally important. There is no single “best material” independent of the job.

ANSI and EN 388: Why the Letters Don't Match

If you source gloves internationally, you may see ANSI A1–A9 on one label and an EN 388 cut letter A–F on another. Both communicate test results, but they belong to different standards and should not be compared by matching the letters or numbers.

Two Standards, Different Scales

ANSI/ISEA 105-2024 • North America

Cut resistance: A1 through A9

A1A2A3A4A5A6A7A8A9
EN 388:2016+A1:2018 • Europe

ISO 13997 cut test: A through F

ABCDEF

Do not compare the labels directly: ANSI A5 is not the same category as EN 388 E or any similarly named level. Confirm the test method and rating for the glove.

EN 388 also covers other mechanical hazards such as abrasion, tear, and puncture; its ISO 13997 cut result is reported from A to F. When comparing gloves, check which test produced the rating, not just the largest-looking symbol on the package.

Four Cut-Glove Myths Worth Retiring

Myth 1: “A9 gloves are cut-proof.” No glove is cut-proof. A rating is a controlled laboratory result; real-world edge shape, movement, force, wear, and fit can change the risk.

Myth 2: “Cut-resistant means puncture-resistant.” A sharp needle, point, or wire end creates a different hazard. Puncture and needle resistance require their own appropriate tests and selection.

Myth 3: “Thicker always means safer.” Specialized yarns can provide high cut resistance without excessive thickness. Thickness alone does not tell you the rating.

Myth 4: “Gloves are always safer around machines.” Rotating or moving machinery can create entanglement hazards. Follow machine-specific procedures and your site's safety assessment before wearing gloves near moving equipment.

The 60-Second Glove Selection Checklist

  • Identify the hazard: blade edge, glass, metal burr, abrasion, puncture point, heat, or something else?
  • Check the rating: match cut performance—and any separate puncture or abrasion needs—to the assessed risk.
  • Test fit and handling: can the worker grip, move, and complete the task without the glove slipping or interfering?
  • Consider the full environment: wet or oily surfaces, washing, glove wear, chemicals, food-contact needs, and machine movement.

Quick Questions People Ask

Is ANSI A5 always enough for sheet metal?

No universal cut level applies to all sheet-metal tasks. Thickness, edge sharpness, burrs, handling method, and other hazards vary; the rating should follow the site's hazard assessment.

Is an ANSI A9 glove better than an A4 glove?

It has a higher laboratory cut classification. Whether it is the better work glove depends on fit, grip, comfort, dexterity, and other required protections.

Can cut-resistant gloves stop knife tips or needles?

Do not assume so. Cut ratings and puncture protection measure different hazards, and needle puncture is a distinct concern requiring specific evidence.

The Bottom Line

The smartest cut glove isn't automatically the highest-rated one. It's the glove selected for the real hazard. Use ANSI or EN ratings to understand tested cut resistance, then evaluate the glove's other properties and the task before putting it to work.